AMX APEX Destiny 6100 Especificaciones Pagina 66
- Pagina / 84
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
66
User Code Terms
User Code Options
Changing user codes: To change user code, in keypad mode, enter a full function user code (default user 1 is
1,2,3,4), followed by the 7 digit. The system will speak "ENTER USER NUMBER." Press
the 2-digit number (01-32) for the user code you wish to change. You will then hear
"ENTER CODE (the number you selected)". The next four digits pressed will be the new
code. After the fourth digit, the system will speak "EXIT".
Removing user codes: Follow the user code sequence and press the A key when prompted for the user code.
NOTE: Code 1 cannot be removed; only changed.
User Code Options: The locations below each user number control the capabilities of each code. Add the
option values for each user and program the value in the appropriate location.
Duress: When this option is enabled, the user code will issue a silent duress code to the central
station.
Disappearing activations: User codes 2-32 can be programmed as disappearing codes. A disappearing code
remains active for the number of times programmed in location 0129. When a code
becomes inactive, a user can reset the disappearing counter by changing the disarm
code.
Master functions: Adding this option allows a code to enter into bypass mode, extended monitor, and
change user codes.
Remote telephone: Allows use of the code from any off site touch tone phone.
Wired/wireless keypads: Allows use of the code on system keypads.
Local telephones: Allows use of the code on in-house touch tone phones.
Send Open report: Each time the code is used for disarming a report is sent to the central station and/or the
event memory log depending on the Open Report dialing options.
Send Close report: Each time the code is used for arming a report is sent to the central station and/or the
event memory log depending on the Close Report dialing options.
Program Code Options: Works the same as other user code yet applies to the program mode access code.
Assigning Codes to Areas: First decide which area or areas will be controlled by each user code. Select the
appropriate location for the desired user location. Enter the total for all areas assigned
to the user code.
Example: To have user code 3 control areas 1, 2 and 3, program 007 (001 + 002 + 004)
in location 0813.
Split arming is not permitted in UL installations.
- DESTINY 6100 1
- Software Revisions 4
- Table of Contents 5
- System Options and Times 6
- Central Station Features 6
- User Codes 7
- Control Channels 7
- Specifications 8
- Inserting the Cabinet Lock 11
- Mounting the Control Board 11
- To House 12
- From Phone 12
- Wiring Notes 13
- System Terminals 14
- X-10 Interface Cord 16
- Program Mode 18
- Locations and Values 18
- Automated Locations 18
- Exiting Program Mode 18
- Programming 18
- Quick Start 19
- System Input Overview 20
- Programming System Inputs 20
- System Setup Example 21
- Using This Manual: 22
- Program a Zone 23
- Zone Questions 23
- * Zone Type 24
- Zone Options 1 24
- Zone Options 2 24
- Hardware Device Types 25
- Predefined Zone Assignments 25
- Hardwire Inputs 26
- 5816 (MN) 5817 27
- Button Type Devices 28
- Button Functions 29
- Editing Zone Programming 30
- Deleting a Zone 30
- Smoke Verification 33
- Speaker (Bell) Supervision 34
- RF Jam Detection 34
- System Options - Group 1 36
- System Options - Group 2 36
- System Options - Group 3 36
- System Options - Group 4 37
- System Options - Group 5 37
- System Options - Group 6 37
- System Access Codes 37
- System Times 38
- Monitor Trouble Conditions 38
- Bypass Options 38
- Phone Access Options 39
- Event Memory Log 39
- Communicator Times 46
- Two-Way Voice Options 46
- Two-Way Digit Assignments 47
- Report Codes 49
- Dialer Options 51
- Communicator Diagnostics 51
- User Communicator Test 51
- Central Station Terms 52
- Key Function Values 56
- Keypad Option 56
- Keypad Functions 57
- TS16 Group 1 57
- TS16 Group 2 57
- Keypad Area Assignment 57
- User Code + Digit Functions 58
- Extended Monitor Times 58
- Vocabulary 59
- Keypad Function Terms 61
- User Code Options 65
- Disappearing Code Activations 65
- Assigning User Codes to Areas 65
- User Code Terms 66
- Automation Overview 67
- Automation Example 67
- Channel Activations 68
- Control Channel Options 1 69
- Control Channel Options 2 69
- Control Channel Options 3 69
- Control Channel Options 4 69
- Control Channel Locations 70
- System Triggers 71
- X-10 Options 71
- Output Control Assignments 72
- Chain Group Assignments 73
- Control Channel Terms 74
- ADEMCO LIMITED WARRANTY 84
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AMX APEX Destiny 6100
(18 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales