AMX APEX Destiny 6100 Especificaciones Pagina 26
- Pagina / 84
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
26
Hardwire Inputs
System Controller
2 digit Input Number: Enter the hardwire loop on the system controller being used. Valid inputs are 1-16.
The default for this input type is a single end-of-line resistor. This option can be changed to no end-
of-line resistor or full 2 resistor supervision by entering the appropriate value in the locations below.
Options Value
Speaker supervised Zone
...................................................................................................
008
Treat trouble as an activation
............................................................................................
016
2 end-of-line resistor supervision
........................................................................................
064
No end of line resistor (Has not been evaluated for a UL installation)
..............................
128
Default (1 end-of-line resistor)
...........................................................................................
000
HWB416 Zone Expansion Board
1 digit group number: Each HWB416 has two groups of 8 zones that are separately controlled by dip switches.
Inputs labeled 1-8 are the 1st group and 9-16 are the second group. If a second HWB416
is added to the system, the 1st section would be group three and inputs 9-16 would be
group four. Enter the appropriate group number for the desired input. Valid inputs are 1-
8 (lower inputs on HWB416 #1 through the high group of inputs on HWB416 #4).
1 digit input number: Enter the input number from the selected group. Lower inputs (1-8) are entered as written
on the HWB416. For zones in the high group (9-16), subtract 8.
Example: To program input 15 from group 4 (HWB416 #2) enter input number 7
The default for this input type is a single end-of-line resistor. This option can be changed to full 2
resistor supervision by entering the appropriate value in the locations below.
Options Value
2 end-of-line resistor supervision
........................................................................................
128
Default (1 end-of-line resistor)
...........................................................................................
000
System Smoke Loop
There are no additional questions for this input type.
Local Telephone
While in local phone keypad mode, a user can activate a zone by entering 5 zeros. This zone type is traditionally
programmed as a 24 hour panic. There are no additional questions for this input type.
Phone Line Monitor
The phone line monitor input becomes active upon loss of phone line. For notification at the keypad, this input can
be programmed as an auxiliary zone type for enunciation at the keypad, a day zone for extended monitoring and
alerts while armed, or a 24 hour panic for alarm activation upon loss of phone line (not recommended). There are
no additional questions for this input type.
- DESTINY 6100 1
- Software Revisions 4
- Table of Contents 5
- System Options and Times 6
- Central Station Features 6
- User Codes 7
- Control Channels 7
- Specifications 8
- Inserting the Cabinet Lock 11
- Mounting the Control Board 11
- To House 12
- From Phone 12
- Wiring Notes 13
- System Terminals 14
- X-10 Interface Cord 16
- Program Mode 18
- Locations and Values 18
- Automated Locations 18
- Exiting Program Mode 18
- Programming 18
- Quick Start 19
- System Input Overview 20
- Programming System Inputs 20
- System Setup Example 21
- Using This Manual: 22
- Program a Zone 23
- Zone Questions 23
- * Zone Type 24
- Zone Options 1 24
- Zone Options 2 24
- Hardware Device Types 25
- Predefined Zone Assignments 25
- Hardwire Inputs 26
- 5816 (MN) 5817 27
- Button Type Devices 28
- Button Functions 29
- Editing Zone Programming 30
- Deleting a Zone 30
- Smoke Verification 33
- Speaker (Bell) Supervision 34
- RF Jam Detection 34
- System Options - Group 1 36
- System Options - Group 2 36
- System Options - Group 3 36
- System Options - Group 4 37
- System Options - Group 5 37
- System Options - Group 6 37
- System Access Codes 37
- System Times 38
- Monitor Trouble Conditions 38
- Bypass Options 38
- Phone Access Options 39
- Event Memory Log 39
- Communicator Times 46
- Two-Way Voice Options 46
- Two-Way Digit Assignments 47
- Report Codes 49
- Dialer Options 51
- Communicator Diagnostics 51
- User Communicator Test 51
- Central Station Terms 52
- Key Function Values 56
- Keypad Option 56
- Keypad Functions 57
- TS16 Group 1 57
- TS16 Group 2 57
- Keypad Area Assignment 57
- User Code + Digit Functions 58
- Extended Monitor Times 58
- Vocabulary 59
- Keypad Function Terms 61
- User Code Options 65
- Disappearing Code Activations 65
- Assigning User Codes to Areas 65
- User Code Terms 66
- Automation Overview 67
- Automation Example 67
- Channel Activations 68
- Control Channel Options 1 69
- Control Channel Options 2 69
- Control Channel Options 3 69
- Control Channel Options 4 69
- Control Channel Locations 70
- System Triggers 71
- X-10 Options 71
- Output Control Assignments 72
- Chain Group Assignments 73
- Control Channel Terms 74
- ADEMCO LIMITED WARRANTY 84
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AMX APEX Destiny 6100
(18 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales