AMX APEX Destiny 6100 Especificaciones Pagina 44
- Pagina / 84
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
44
Duration between The length of time the system pauses before saying "Entry Detected." The shortest time
pre-alarm cycles: period is three seconds (000). Any value in this location is added to the default 3
seconds.
Burg tone before speech: The length of time the system will create a burglary tone before speech.
Fire cut off and reset: The length of time the system will stay in alarm without a disarm before the system
stops the sirens and waits for another zone activation. Fire cut off and reset is not
permitted in a UL installation.
Phone samples: The built in phone monitor circuit can be adjusted based on the installation location.
Every four seconds, the phone line is sampled, this option determines the number of
samples needed for the panel to determine that a valid phone line has been connected
or removed. In locations subject to brief phone outages use a higher number, in
locations that have reliable phone service use a lower number. The default 6 works
best in most applications.
User Test Timeout: Controls the amount of time before the User Test Mode will automatically time out.
Answer service time: This option is active only when Answer Service Override is enabled. This value
determines the amount of time the panel will wait for a second call after hearing two
rings on the first call.
Automatic Arming and Disarming
Arm State: To automatically arm the system, include AWAY or HOME in the total for the
"Automatic Arm / Disarm" option.
Disarm: To automatically disarm the system, include Disarm in the total for the
"Automatic Arm / Disarm" option.
Force arm w/ open zones: To automatically force arm around open zones, include force arm around open zones in
the total for the "Automatic Arm / Disarm" option. If this option is not used the panel
will not automatically if a zone is open.
5 day cycle: The automatic arm/disarm feature will occur every day unless the 5 day cycle is
included in the "Automatic Arm / Disarm" option. The 5 day cycle is Monday through
Friday.
Monitor Trouble Conditions
Monitor trouble: The system can speak and indicate a high current situation, control low battery, and a
failure to complete a digital communication as trouble conditions at the keypad.
Entering 001 will enable speech and show the condition at the keypad while 000
disables this feature. This feature must be enabled in a UL installation.
Battery trouble: Enables Battery test every 3 minutes. If the backup battery is under 10 volts, low
battery can be displayed at the keypad and / or sent to the central station. This option
must be enabled in a UL installation.
- DESTINY 6100 1
- Software Revisions 4
- Table of Contents 5
- System Options and Times 6
- Central Station Features 6
- User Codes 7
- Control Channels 7
- Specifications 8
- Inserting the Cabinet Lock 11
- Mounting the Control Board 11
- To House 12
- From Phone 12
- Wiring Notes 13
- System Terminals 14
- X-10 Interface Cord 16
- Program Mode 18
- Locations and Values 18
- Automated Locations 18
- Exiting Program Mode 18
- Programming 18
- Quick Start 19
- System Input Overview 20
- Programming System Inputs 20
- System Setup Example 21
- Using This Manual: 22
- Program a Zone 23
- Zone Questions 23
- * Zone Type 24
- Zone Options 1 24
- Zone Options 2 24
- Hardware Device Types 25
- Predefined Zone Assignments 25
- Hardwire Inputs 26
- 5816 (MN) 5817 27
- Button Type Devices 28
- Button Functions 29
- Editing Zone Programming 30
- Deleting a Zone 30
- Smoke Verification 33
- Speaker (Bell) Supervision 34
- RF Jam Detection 34
- System Options - Group 1 36
- System Options - Group 2 36
- System Options - Group 3 36
- System Options - Group 4 37
- System Options - Group 5 37
- System Options - Group 6 37
- System Access Codes 37
- System Times 38
- Monitor Trouble Conditions 38
- Bypass Options 38
- Phone Access Options 39
- Event Memory Log 39
- Communicator Times 46
- Two-Way Voice Options 46
- Two-Way Digit Assignments 47
- Report Codes 49
- Dialer Options 51
- Communicator Diagnostics 51
- User Communicator Test 51
- Central Station Terms 52
- Key Function Values 56
- Keypad Option 56
- Keypad Functions 57
- TS16 Group 1 57
- TS16 Group 2 57
- Keypad Area Assignment 57
- User Code + Digit Functions 58
- Extended Monitor Times 58
- Vocabulary 59
- Keypad Function Terms 61
- User Code Options 65
- Disappearing Code Activations 65
- Assigning User Codes to Areas 65
- User Code Terms 66
- Automation Overview 67
- Automation Example 67
- Channel Activations 68
- Control Channel Options 1 69
- Control Channel Options 2 69
- Control Channel Options 3 69
- Control Channel Options 4 69
- Control Channel Locations 70
- System Triggers 71
- X-10 Options 71
- Output Control Assignments 72
- Chain Group Assignments 73
- Control Channel Terms 74
- ADEMCO LIMITED WARRANTY 84
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AMX APEX Destiny 6100
(18 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales