AMX APEX Destiny 6100 Especificaciones Pagina 32
- Pagina / 84
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
32
Zone Options 2
Area: When Split Arming is enabled, this option determines which of the 8 areas the zone is
assigned. Do not add multiple areas.
Suppress monitor: This option will prevent a zone from being enunciated when the system is in monitor
mode.
Suppress open: This option will prevent the system from speaking the word "OPEN" at the end of a zone
description. This is useful when the object being monitored does not have an open or
closed state such as a driveway motion detector.
Suppress siren: This option will cause a zone that normally produces an audible activation to produce a
silent alarm. The activation appears in system status and on an LCD display, however
no audible indication is given.
System and HWB416 Inputs
Two resistor supervision: When an input is programmed to be completely supervised, the control will recognize
traditional opens and closes as well as a break or short in the loop. A break or short
can produce a zone trouble condition which will be shown on the keypad. If
programmed, trouble condition can cause an alarm condition if the trouble occurs while
the system is armed. A trouble will clear when the loop has been corrected. See
"Hardware and Wiring" for a wire loop diagram. Fire zones are fully supervised with
one resistor and can not be wired with a 2 resistor combination.
No end-of-line resistor: With this option selected, the panel does not look for a 4.7KW resistor on the input loop.
This option can only be used with normally closed loops. No End-of Line Resistor is not
evaluated for UL installation.
Using a TS16 - Only use between 32 - 127 degrees F
Enable TS16: If a TS16 is installed, use this option to enable the TS16 options. TS16 sensors not
evaluated for UL installation.
Speak transmissions: A TS16 sends a temperature each time the temperature changes. In addition, a TS16
sends a status message every minute or ten minutes based on the dip switch setting.
With this option set, the panel will speak the temperature each time a message is
received from the TS16.
Temperature with time: With this option set the selected TS16's description and temperature will be spoken
whenever time is requested. Note: option 004 in System Options - Group 6 must be set
for this option to function.
Use High/Low Setting: This option determines if the High and/or Low trip points should be used to cause a zone
activation. If neither option is selected, the zone will never show open.
Hysteresis: This setting specifies how much the temperature must fall below the high setpoint or rise
above the low setpoint for a close to occur. Hysterics settings of 2 and 4 can be added
(192) for a hysterics of 6 degrees. If values 64 and 128 are not used, the hysterics is 1
degree.
High/Low setting: These temperature settings determine when the panel will show the attached zone as
open or closed. The zone will show open when the setpoint is reached. To prevent
open/close cycling when the temperature is around the setpoint, a hysterics option is
available.
Note: If a Low setpoint and High setpoint are being used then:
Low + hysterics must be less then High - hysterics. See "Key Function Values" in the
Keypad Functions section for definition of terms.
- DESTINY 6100 1
- Software Revisions 4
- Table of Contents 5
- System Options and Times 6
- Central Station Features 6
- User Codes 7
- Control Channels 7
- Specifications 8
- Inserting the Cabinet Lock 11
- Mounting the Control Board 11
- To House 12
- From Phone 12
- Wiring Notes 13
- System Terminals 14
- X-10 Interface Cord 16
- Program Mode 18
- Locations and Values 18
- Automated Locations 18
- Exiting Program Mode 18
- Programming 18
- Quick Start 19
- System Input Overview 20
- Programming System Inputs 20
- System Setup Example 21
- Using This Manual: 22
- Program a Zone 23
- Zone Questions 23
- * Zone Type 24
- Zone Options 1 24
- Zone Options 2 24
- Hardware Device Types 25
- Predefined Zone Assignments 25
- Hardwire Inputs 26
- 5816 (MN) 5817 27
- Button Type Devices 28
- Button Functions 29
- Editing Zone Programming 30
- Deleting a Zone 30
- Smoke Verification 33
- Speaker (Bell) Supervision 34
- RF Jam Detection 34
- System Options - Group 1 36
- System Options - Group 2 36
- System Options - Group 3 36
- System Options - Group 4 37
- System Options - Group 5 37
- System Options - Group 6 37
- System Access Codes 37
- System Times 38
- Monitor Trouble Conditions 38
- Bypass Options 38
- Phone Access Options 39
- Event Memory Log 39
- Communicator Times 46
- Two-Way Voice Options 46
- Two-Way Digit Assignments 47
- Report Codes 49
- Dialer Options 51
- Communicator Diagnostics 51
- User Communicator Test 51
- Central Station Terms 52
- Key Function Values 56
- Keypad Option 56
- Keypad Functions 57
- TS16 Group 1 57
- TS16 Group 2 57
- Keypad Area Assignment 57
- User Code + Digit Functions 58
- Extended Monitor Times 58
- Vocabulary 59
- Keypad Function Terms 61
- User Code Options 65
- Disappearing Code Activations 65
- Assigning User Codes to Areas 65
- User Code Terms 66
- Automation Overview 67
- Automation Example 67
- Channel Activations 68
- Control Channel Options 1 69
- Control Channel Options 2 69
- Control Channel Options 3 69
- Control Channel Options 4 69
- Control Channel Locations 70
- System Triggers 71
- X-10 Options 71
- Output Control Assignments 72
- Chain Group Assignments 73
- Control Channel Terms 74
- ADEMCO LIMITED WARRANTY 84
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AMX APEX Destiny 6100
(18 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales