AMX APEX Destiny 6100 Especificaciones descargar pdf (Pagina 14)

System Terminals

House Phones: The R1 and T1 terminals provide telephone service to the house if the installation

contains an RJ-31X terminal block for true phone line seizure.

Telephone Company: The incoming telephone service is wired through an RJ-31X jack to the R and T

terminals on the control panel. If regular phone service is unavailable, the system will

provide power and a distinct system tone to all in house phones.

Speakers: The control panel contains amplified internal and external siren drivers. Both internal

and external speaker connections require 8W , 10 watt (minimum) speakers. The "EXT"

and "COM" (speaker common) terminals provide full volume audio during activation.

Mount the external speaker(s) in an area that is unaccessible to intruders and will

provide a sufficient volume during an activation.

The INT and COM terminals produce speech, low volume monitor beeps, keypad

echo beeps, system status, pre-alarm warning, and a high volume alert during

activation. Typically, in non UL installations, the speakers (16W) in the RK series

keypads are used as the only source for providing internal system audio; however in a

UL installation the RK series keypads must be supplemented with an Ademco 705

speaker connected to the "EXT" and "COM" terminals. See Specifications for

compatible speakers.

Wire all speakers in a series/parallel combination that does not allow the impedance for

either the internal or external output to drop below 4W.

Transformer (AC Power): Use a 16.5 VAC, 40 VA transformer (supplied) to supply AC power. Do not connect the

transformer to a switched AC outlet. If an AC failure occurs, after 1 minute

(programmable) the system will speak "POWER OFF", the keypad power LED will turn

off, and the keypad status LED will begin to flash. After requesting system status the

system will speak "POWER OFF" and the status LED will become solid. AC failure and

restore conditions can be transmitted to the central station.

2-Wire Smoke Detectors: 2-wire smoke detectors are connected to the "SMK+" and "SMK-" terminals. Be certain

to observe polarity. Smoke power reset is built into the panel by entering a valid full

function user code followed by the "6" digit. A 4.7KW resistor must be wired in parallel

with the last detector in the loop. If a resistor is not used, or if there is a break in the

loop, a TROUBLE indication will occur. Up to 12 2-wire smoke detectors can be

circuit can be indicated at the keypad and/or communicated to the central station.

4-Wire Smoke Detectors: The "SMK+" terminal supplies up to 1.85 AMPs of power. A 4.7KW resistor must be

wired in parallel with the detector and wired to a zone input. Power is drawn from the

SMK+ and COM terminals. Smoke power reset is built into the panel and is reset by

entering a valid full function user code followed by the 6 digit. A high current situation

on the smoke power circuit can be indicated at the keypad and/or communicated to the

central station. Use of 4-wire Smoke Detectors not evaluated for UL installation.

Auxiliary Power: 12V+ Auxiliary power for hardwire devices such as motion detectors and glass break

detectors is available on the "AUX" terminal. The auxiliary output is protected at 1.85

Amps. A high current situation can be indicated at the keypad and/or communicated to

the central station.

The Destiny-6100 is compatible with the ADEMCO 4142-BLK removable terminal strips. If

necessary, these connectors allow for quick replacement of the control board.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 83 84

Comentarios a estos manuales

Sin comentarios

AMX APEX Destiny 6100 Especificaciones Pagina 14

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AMX APEX Destiny 6100