AMX APEX Destiny 6100 Especificaciones Pagina 51
- Pagina / 84
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
51
'LDOHU/ ( ' 0 HVVDJH &RUUHFWLYH0 HDVXUH
([WHQGHG RQ IROORZ HG E\ RQHVKRUWRQDQGRII 6 XFFHVVIXO F RP P XQLFDWLRQ 1 RQH
7ZRVKRWRQDQG RI I V 1 R S KRQH QXP EHU&KHFN S KRQH QXP EHUSURJ UDPPLQJ
([
WH
Q
GHG R
Q
IROORZ HG E\ WKUHHR
Q
D
Q
G RI I
V
1 RGLDOWR
QH
&KHFNSKR
Q
HOL
Q
HFR
QQ
HFWLR
Q
([
WH
Q
GHG R
Q
IROORZ HGE\ IRXUR
Q
D
Q
G R I I
V
1 RKD
Q
GVKDNHRUEXV\VLJ
Q
D
O
&KHFN5 HSRUWL
Q
J
)
RUPDWD
Q
G
Q
XP EH
U
([
WH
Q
GHG R
Q
IROORZ HGE\ ILYHR
Q
D
Q
G R I I
V
1 RNLVVRIIWR
QH
&KHFN5 HSRUWL
Q
J
)
RUPD
W
Dialer Options
Options - Enter total Value
Dial Phone #1
....................................................................................................................
001
Dial Phone #2
....................................................................................................................
002
Enable two-way voice/listen in (Not permitted in a UL installation)
.................................
004
Dial alternate number if first choice fails
..........................................................................
008
Record this report type in Event Memory Log
....................................................................
128
Default (for Fire and Burg)
................................................................................................
129
Communicator Diagnostics
Dialer LED: The communicator has a built in diagnostic feature which can be very valuable in trouble
shooting. The red Dialer LED indicates successful communication with the central station and if
the communication fails it indicates at which stage the trouble occurred. Any time the
communicator does not make a successful communication (except in the case of not having a
good phone number programmed) it will make the programmed number of attempts. The message
for no phone number will only be shown once. If a digital communication is initiated when the
Phone LED is off (no dial tone present), the control will not attempt to dial out. Diagnostics will
not be given. The only time three flash diagnostics will appear is when the phone line is present
at the beginning of a communication and no dial tone is detected. If communication is
unsuccessful, remove everything from R, T except the phone line. This includes test sets, as they
may load the phone lines down, even with the monitor switched on. The program mode 9960 can
be used to echo the entire communicator session though the internal speakers.
User Communicator Test
A user Communicator test is integrated into the system to allow an end user to test the system on a regular basis.
Enter a valid user code followed by the "0" digit. The system will speak "Enter User Test Mode." A User
Communicator Test report is sent to the central station. WHILE IN TEST MODE THE SYSTEM CEASES TO BE A
SECURITY SYSTEM. As each zone is tripped (including 24 hour zones) the system will speak the zone description
followed by "active." After 3 minutes (programmable) the panel will automatically exit user test mode. To exit
user test mode manually, enter a user code followed by the "0" digit.
- DESTINY 6100 1
- Software Revisions 4
- Table of Contents 5
- System Options and Times 6
- Central Station Features 6
- User Codes 7
- Control Channels 7
- Specifications 8
- Inserting the Cabinet Lock 11
- Mounting the Control Board 11
- To House 12
- From Phone 12
- Wiring Notes 13
- System Terminals 14
- X-10 Interface Cord 16
- Program Mode 18
- Locations and Values 18
- Automated Locations 18
- Exiting Program Mode 18
- Programming 18
- Quick Start 19
- System Input Overview 20
- Programming System Inputs 20
- System Setup Example 21
- Using This Manual: 22
- Program a Zone 23
- Zone Questions 23
- * Zone Type 24
- Zone Options 1 24
- Zone Options 2 24
- Hardware Device Types 25
- Predefined Zone Assignments 25
- Hardwire Inputs 26
- 5816 (MN) 5817 27
- Button Type Devices 28
- Button Functions 29
- Editing Zone Programming 30
- Deleting a Zone 30
- Smoke Verification 33
- Speaker (Bell) Supervision 34
- RF Jam Detection 34
- System Options - Group 1 36
- System Options - Group 2 36
- System Options - Group 3 36
- System Options - Group 4 37
- System Options - Group 5 37
- System Options - Group 6 37
- System Access Codes 37
- System Times 38
- Monitor Trouble Conditions 38
- Bypass Options 38
- Phone Access Options 39
- Event Memory Log 39
- Communicator Times 46
- Two-Way Voice Options 46
- Two-Way Digit Assignments 47
- Report Codes 49
- Dialer Options 51
- Communicator Diagnostics 51
- User Communicator Test 51
- Central Station Terms 52
- Key Function Values 56
- Keypad Option 56
- Keypad Functions 57
- TS16 Group 1 57
- TS16 Group 2 57
- Keypad Area Assignment 57
- User Code + Digit Functions 58
- Extended Monitor Times 58
- Vocabulary 59
- Keypad Function Terms 61
- User Code Options 65
- Disappearing Code Activations 65
- Assigning User Codes to Areas 65
- User Code Terms 66
- Automation Overview 67
- Automation Example 67
- Channel Activations 68
- Control Channel Options 1 69
- Control Channel Options 2 69
- Control Channel Options 3 69
- Control Channel Options 4 69
- Control Channel Locations 70
- System Triggers 71
- X-10 Options 71
- Output Control Assignments 72
- Chain Group Assignments 73
- Control Channel Terms 74
- ADEMCO LIMITED WARRANTY 84
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AMX APEX Destiny 6100
(18 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales