AMX APEX Destiny 6100 Especificaciones Pagina 30
- Pagina / 84
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
30
Editing Zone Programming
Once a zone has been programmed, the system provides a quick method for editing zone values. Enter 9,9,4,0
followed by the zone number. As each input prompt is played, press F1 and the system will replay the current
value. To change the configuration, enter a new value. To accept a current value, press F2. The Monitor button
will return to the previous prompt. The Monitor button will not return to prompts once the system has asked for F2
to confirm. Any changes made only take effect if the final question is answered and the system speaks exit.
Deleting a Zone
A zone can be deleted by entering a device type of 255.
Programming System Inputs to Zones Terms
System Input Automated Programming Locations
RF Strength Mode: This mode reduces the sensitivity of the receiver and speaks the serial number for all
5800 signals.
Exit Program Mode: Removes the system from program mode and places the system in keypad mode.
Zone Types
Exterior Instant: Exterior instant zones instantly sound an alarm when the system is armed to HOME,
AWAY or Night. When the system is not armed, monitor mode is active, and the zone
is programmed to show open/close status at the keypad, the system will speak the zone
description or sound a monitor beep when the zone input is activated. Exterior Instant
zones can be programmed to sound an alarm when the input is activated during an exit
delay (System Options - Group 2, option 008). Otherwise, the exterior instant zone will
respond in the same manner as when the system is not armed.
Exterior Delay #1: Tripping an exterior delay input places the system into a pre-alarm mode if the system is
armed to AWAY or HOME (unless "No entry delay for Exterior Delay #1 in Home" is
selected in System Options - group 2). The system refers to entry delay time #1 to
determine the pre-alarm duration. If pre-alarm expires without a user entering a valid
disarm code, the system will sound an alarm. When the system is not armed, monitor
mode is active, and the zone is programmed to show open/close status at keypad, the
system will speak the zone description or sound a monitor beep when the zone input is
activated. During an exit delay, Exterior Delay zones respond in the same manner as
when the system is not armed. In Night mode, this zone type acts an exterior instant.
Exterior Delay #2: Same as above but uses programmable entry delay time #2.
Interior Instant: The interior instant zones are active in the AWAY mode only. No monitor function is
provided for interior zones (except during extended monitor). During an exit delay, an
opening is ignored.
Interior Delay #1: Same as Exterior Delay #1 except active only in AWAY mode and no monitor is
provided.
Interior Delay #2: Same as Exterior Delay #2 except active only in AWAY and Night mode and no monitor
is provided. Uses delay time #2.
Fire: Fire zones respond with short high volume tones over the internal and external speakers.
The system will alternate between the tones and speaking "FIRE, FIRE," followed by the
up-to-four-word zone description, and "REMAIN CALM, LEAVE IMMEDIATELY."
Panic: Panic zones respond with a high volume alert on both the internal and external speaker.
The alert consists of a pulsed tone followed by "ALERT, ALERT", and the up-to-four-word
description of the zone.
- DESTINY 6100 1
- Software Revisions 4
- Table of Contents 5
- System Options and Times 6
- Central Station Features 6
- User Codes 7
- Control Channels 7
- Specifications 8
- Inserting the Cabinet Lock 11
- Mounting the Control Board 11
- To House 12
- From Phone 12
- Wiring Notes 13
- System Terminals 14
- X-10 Interface Cord 16
- Program Mode 18
- Locations and Values 18
- Automated Locations 18
- Exiting Program Mode 18
- Programming 18
- Quick Start 19
- System Input Overview 20
- Programming System Inputs 20
- System Setup Example 21
- Using This Manual: 22
- Program a Zone 23
- Zone Questions 23
- * Zone Type 24
- Zone Options 1 24
- Zone Options 2 24
- Hardware Device Types 25
- Predefined Zone Assignments 25
- Hardwire Inputs 26
- 5816 (MN) 5817 27
- Button Type Devices 28
- Button Functions 29
- Editing Zone Programming 30
- Deleting a Zone 30
- Smoke Verification 33
- Speaker (Bell) Supervision 34
- RF Jam Detection 34
- System Options - Group 1 36
- System Options - Group 2 36
- System Options - Group 3 36
- System Options - Group 4 37
- System Options - Group 5 37
- System Options - Group 6 37
- System Access Codes 37
- System Times 38
- Monitor Trouble Conditions 38
- Bypass Options 38
- Phone Access Options 39
- Event Memory Log 39
- Communicator Times 46
- Two-Way Voice Options 46
- Two-Way Digit Assignments 47
- Report Codes 49
- Dialer Options 51
- Communicator Diagnostics 51
- User Communicator Test 51
- Central Station Terms 52
- Key Function Values 56
- Keypad Option 56
- Keypad Functions 57
- TS16 Group 1 57
- TS16 Group 2 57
- Keypad Area Assignment 57
- User Code + Digit Functions 58
- Extended Monitor Times 58
- Vocabulary 59
- Keypad Function Terms 61
- User Code Options 65
- Disappearing Code Activations 65
- Assigning User Codes to Areas 65
- User Code Terms 66
- Automation Overview 67
- Automation Example 67
- Channel Activations 68
- Control Channel Options 1 69
- Control Channel Options 2 69
- Control Channel Options 3 69
- Control Channel Options 4 69
- Control Channel Locations 70
- System Triggers 71
- X-10 Options 71
- Output Control Assignments 72
- Chain Group Assignments 73
- Control Channel Terms 74
- ADEMCO LIMITED WARRANTY 84
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad AMX APEX Destiny 6100
(18 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales