AMX NI-3100 Especificaciones Pagina 26
- Pagina / 160
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Initial Configuration and Firmware Upgrade
16
NetLinx Integrated Controllers- WebConsole & Programming Guide (FMv3)
17. Right-click the System number and select Refresh System. This establishes a new connection to the
System and populates the list with the current devices (and their firmware versions) on your system.
Upgrading the NI Controller Firmware Via IP
1. Follow the procedures outlined within the Communicating Via an IP Address section on page 10 to
connect to the target NI device via the web.
2. After Studio has established a connection to the target Master, click the OnLine Tree tab of the
Workspace window to view the devices on the System. The default System value is one (1).
3. Right-click the associated System number and select Refresh System. This establishes a new connection
to the specified System and populates the list with devices on that system. The communication method is
highlighted in green on the bottom of the NetLinx Studio window.
4. After the Communication Verification dialog window verifies active communication between the PC and
the NI unit, verify the Integrated Controller appears in the OnLine Tree tab (FIG. 15) of the Workspace
window (ex: NI-4000 or NI-700). This entry is different than the NI Master which uses a device value of
00000 (see below):
5. If the NI Controller firmware being used is not current, download the latest Kit file by first logging in to
www.amx.com and then navigating to Tech Center > Firmware Files, where you can locate the desired
file from within the NI Series Device (Integrated Controller) section of the web page.
6. Click on the desired Kit file link and after you’ve accepted the Licensing Agreement, verify you have
downloaded the Integrated Controller firmware (Kit) file to a known location.
7. From within Studio, select Tools > Firmware Transfers > Send to NetLinx Device from the Main menu
to open the Send to NetLinx Device dialog (FIG. 16). Verify the target’s System number matches the
value listed within the active System folder in the OnLine Tree tab of the Workspace.
The Device must match the entry for the on-board Integrated Controller (ex: NI-4100 or NI-700) device.
The OUTPUT and INPUT LEDs alternately blink to indicate the on-board Master is
incorporating the new firmware. Allow the Master 20 - 30 seconds to reboot and fully
restart.
FIG. 15 Sample NetLinx Workspace window (showing separate NI-Master and Controller)
On-board Integrated Controller (NI-X000)
Unbound Dynamic Device
NetLinx Studio version
On-board NI Master
(NI-X000_Master) - Device 0
- Last Revised: 5/25/2012 1
- Table of Contents 10
- About This Document 12
- Related Documents 13
- Using Zero Configuration 14
- Before You Start 15
- Device Addressing dialog 16
- WebConsole UI Overview 31
- Device Tree 32
- Device Network Settings Pages 33
- ZeroConfig Networking 34
- WebConsole - Security Options 35
- Login Rules 36
- User Name and Password Rules 36
- Allowed Special Characters 36
- Security - System Level 37
- Access Options 38
- Accepting Changes 39
- Configuring Settings 39
- System Security - Group Level 40
- Group Security Details Page 42
- System Security - User Level 44
- Deleting a User 46
- Compression Options 47
- WebConsole - System Options 49
- Diagnostic Options table 54
- Edit Options window 56
- Port Settings 59
- Server Port Settings 59
- SSL Certificate Options 61
- SSL Certificate Entries 62
- Import SSL Certificate window 64
- System - Manage License 68
- System - Manage NetLinx 69
- System - Manage Devices 71
- Manage Devices - Bindings 73
- Adding a User-Defined Device 77
- Editing Polled Port Settings 80
- Manage Devices - URL List 82
- Manage Devices - Log 85
- Manage Devices - Diagnostics 86
- NetLinx Programming 89
- Master SEND_COMMANDs (Cont.) 90
- Port: System 91
- RS232/422/485 Ports Channels 92
- IR / Serial Ports Channels 97
- IR RX Port Channels 97
- IR/Serial SEND_COMMANDs 97
- Input/Output SEND_COMMANDs 103
- I/O SEND_COMMANDs (Cont.) 104
- Overview 105
- Terminal Commands 107
- Terminal Commands (Cont.) 108
- ESC Pass Codes 125
- Setup Security Menu 127
- Security Options Menu 128
- Edit User Menu 129
- Edit Group Menu 129
- Telnet Diagnostics Commands 132
- Linux Telnet Client 133
- IPSec Config file 135
- Internet Key Exchange (IKE) 135
- SpdAddTunnel 138
- SpdAddBypass 139
- SpdAddDiscard 139
- SpdSetProp 140
- SpdSetProp (Cont.) 141
- SpdSetPropAttrib 143
- Manual Key Manager (MKM) 145
- IPSec Security Settings page 153
- Programming API 155
- CLKMGR_GET_ACTIVE_TIMESERVER 156
- (CONSTANT CHAR RECORD[]) 157
- Increase Your Revenue 160
Relacionado con productos y manuales para Gateways / Controladores AMX NI-3100
(40 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales