AMX NI-3100 Especificaciones Pagina 25
- Pagina / 160
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Initial Configuration and Firmware Upgrade
15
NetLinx Integrated Controllers- WebConsole & Programming Guide (FMv3)
Do not use the 2105-03_NI_Master Kit file on anything other than an NI-700/900, since each Master Kit
file is specifically configured to function on a specific NI unit.
9. Enter the System number associated with the target Master (listed in the OnLine Tree tab of the
Workspace window) and verify the Device number value. The Port field is disabled.
10. Click the Reboot Device checkbox to reboot the NI unit after the firmware update process is complete.
11. Click Send to begin the transfer. The file transfer progress is indicated on the bottom-right of the dialog
(FIG. 14).
12. After the last components fails to install, click Done.
13. Click Reboot (from the Tools > Reboot the Master Controller dialog) and wait for the System Master to
reboot.
The STATUS and OUTPUT LEDs should begin to alternately blink during the incorporation. Wait until
the STATUS LED is the only LED to blink.
14. Press Done once until the Master Reboot Status field reads *Reboot of System Complete*.
15. Repeat steps 5 - 9 again (the last component will now successfully be installed).
16. Click Close once the download process is complete.
FIG. 14 Send to NetLinx Device dialog (showing on-board NI_Master firmware update via IP)
Selected Master firmware file
Description field for
Device and System Number
must match the Device and System values
listed in the Workspace window
Firmware download
status
selected Kit file
The Kit file for the NI-2100/3100/4100 Masters begins with 2105_04_NI-X100_Master.
The Kit file for the NI-700/900 Masters begins with 2105-03_NI-X000_Master.
Only upon the initial installation of a new Kit file to an on-board Master will there
be a error message displayed indicating a failure of the last component to
successfully download.
This is part of the NI Master update procedure and requires that the firmware be
reloaded after a reboot of the unit. This consecutive process installs the final
component of the new Kit file.
- Last Revised: 5/25/2012 1
- Table of Contents 10
- About This Document 12
- Related Documents 13
- Using Zero Configuration 14
- Before You Start 15
- Device Addressing dialog 16
- WebConsole UI Overview 31
- Device Tree 32
- Device Network Settings Pages 33
- ZeroConfig Networking 34
- WebConsole - Security Options 35
- Login Rules 36
- User Name and Password Rules 36
- Allowed Special Characters 36
- Security - System Level 37
- Access Options 38
- Accepting Changes 39
- Configuring Settings 39
- System Security - Group Level 40
- Group Security Details Page 42
- System Security - User Level 44
- Deleting a User 46
- Compression Options 47
- WebConsole - System Options 49
- Diagnostic Options table 54
- Edit Options window 56
- Port Settings 59
- Server Port Settings 59
- SSL Certificate Options 61
- SSL Certificate Entries 62
- Import SSL Certificate window 64
- System - Manage License 68
- System - Manage NetLinx 69
- System - Manage Devices 71
- Manage Devices - Bindings 73
- Adding a User-Defined Device 77
- Editing Polled Port Settings 80
- Manage Devices - URL List 82
- Manage Devices - Log 85
- Manage Devices - Diagnostics 86
- NetLinx Programming 89
- Master SEND_COMMANDs (Cont.) 90
- Port: System 91
- RS232/422/485 Ports Channels 92
- IR / Serial Ports Channels 97
- IR RX Port Channels 97
- IR/Serial SEND_COMMANDs 97
- Input/Output SEND_COMMANDs 103
- I/O SEND_COMMANDs (Cont.) 104
- Overview 105
- Terminal Commands 107
- Terminal Commands (Cont.) 108
- ESC Pass Codes 125
- Setup Security Menu 127
- Security Options Menu 128
- Edit User Menu 129
- Edit Group Menu 129
- Telnet Diagnostics Commands 132
- Linux Telnet Client 133
- IPSec Config file 135
- Internet Key Exchange (IKE) 135
- SpdAddTunnel 138
- SpdAddBypass 139
- SpdAddDiscard 139
- SpdSetProp 140
- SpdSetProp (Cont.) 141
- SpdSetPropAttrib 143
- Manual Key Manager (MKM) 145
- IPSec Security Settings page 153
- Programming API 155
- CLKMGR_GET_ACTIVE_TIMESERVER 156
- (CONSTANT CHAR RECORD[]) 157
- Increase Your Revenue 160
Relacionado con productos y manuales para Gateways / Controladores AMX NI-3100
(40 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales