AMX AXD-CP4/PB Especificaciones descargar pdf (Pagina 8)

APPENDIX:

PARAMETERS, VARIABLES & COMMANDS .......................................................APPENDIX A

LIST OF ERRORS, WARNINGS AND TROUBLESHOOTING ..................................APPENDIX B

FAGOR PRODUCTS REFERENCES ....................................................................APPENDIX C

COMPATIBILITY..................................................................................................APPENDIX D

PROTECTIONS ON DRIVES AND MOTORS .........................................................APPENDIX E

AP. APPLICATIONS ......................................................................................................... AP - 1

AP.1 SERCOS CONNECTION WITH THE 8050/55 CNC ...........................................................AP - 1

AP.1.1 CONSIDERATIONS AT THE 8050/55 CNC .....................................................................AP - 2

AP.1.1.1 IDENTIFICATION AND OPERATION MODE .................................................................AP - 2

AP.1.1.1.1 8050/55 IN "0" MODE (EXTERNAL FEEDBACK) ....................................................AP - 3

AP.1.1.1.2 8050/55 CNC IN "1" MODE (MOTOR'S OWN FEEDBACK) .....................................AP - 3

AP.1.1.2 OTHER 8050/55 CNC PARAMETERS .........................................................................AP - 4

AP.1.1.2.1 ON AXIS DRIVES .................................................................................................AP - 5

AP.1.1.2.2 ON SPINDLE DRIVES IN OPEN LOOP. .................................................................AP - 6

AP.1.1.2.3 ON SPINDLE DRIVES IN CLOSED LOOP, M19 OR RIGID TAPPING. .......................AP - 7

AP.1.2 CONSIDERATIONS AT THE DRIVES .......................................................................... AP - 10

AP.1.3 CONTROL SIGNALS PLC8050/55 - DRIVE.................................................................. AP - 11

AP.2 CONNECTION WITH THE FAGOR 8070 CNC ................................................................ AP - 14

AP.3 PARAMETER SET AND GEAR RATIOS ....................................................................... AP - 15

AP.3.1 PARAMETER SET .................................................................................................... AP - 17

AP.3.1.1 SET CHANGE THROUGH DIGITAL INPUTS .............................................................. AP - 17

AP.3.1.2 SET CHANGE THROUGH SERCOS INTERFACE ...................................................... AP - 19

AP.3.2 GEAR RATIOS.......................................................................................................... AP - 20

AP.3.2.1 CHANGE OF GEAR RATIO THROUGH SERCOS INTERFACE .................................. AP - 21

AP.3.2.2 EXAMPLE OF A PLC PROGRAM FOR A GEAR CHANGE AT THE MAIN SPINDLE..... AP - 22

AP.3.2.3 EXAMPLE OF A PLC PROGRAM FOR A PARAMETER SET CHANGE ...................... AP - 25

AP.3.3 SETS AND GEAR RATIOS AT THE DDSSETUP MONITOR .......................................... AP - 28

AP.4 VARIABLE MONITORING ............................................................................................ AP - 29

AP.4.1 PROGRAMMING MODULE AS MONITOR .................................................................. AP - 29

AP.4.2 DIGITAL ELECTRICAL SIGNALS FOR PLC OR MANOEUVER ..................................... AP - 30

AP.4.3 ANALOG OUTPUTS FOR THE "DIAL" ........................................................................ AP - 31

AP.5 HANDLING OF INTERNAL VARIABLES VIA SERCOS ................................................... AP - 32

AP.6 SPINDLE MOTORS AT LOW RPM ............................................................................... AP - 34

AP.7 HALT FUNCTION ........................................................................................................ AP - 35

AP.8 MOTOR STOP DUE TO TORQUE OVERLOAD ............................................................. AP - 36

AP.9 FLUX REDUCTION WITHOUT LOAD............................................................................. AP - 37

DS. DESIGN......................................................................................................................DS - 1

DS.1 AXIS MOTOR AND SERVO DRIVE SELECTION .............................................................DS - 1

DS.1.1 FIRST MOTOR PRE-SELECTION .................................................................................DS - 1

DS.1.2 SECOND MOTOR PRE-SELECTION ...........................................................................DS - 3

DS.1.3 THIRD MOTOR PRE-SELECTION.................................................................................DS - 4

DS.1.4 DRIVE SELECTION.....................................................................................................DS - 5

DS.2 SPINDLE MOTOR AND SERVO DRIVE..........................................................................DS - 6

DS.2.1 POWER DEMANDED FROM A MOTOR FOR A PARTICULAR LOAD .............................DS - 6

DS.2.1.1 POWER REQUIRED BY THE LOAD...........................................................................DS - 7

DS.2.1.2 POWER NEEDED FOR THE ACC / DEC OF THE SPINDLE MOTOR............................DS - 9

DS.2.2 CALCULATION OF ACCELERATION AND BRAKING TIME ........................................... DS - 11

DS.2.3 CALCULATION OF POWER WITH INTERMITTENT LOAD ............................................ DS - 11

DS.2.4 DRIVE SELECTION................................................................................................... DS - 11

DS.3 POWER SUPPLY SELECTION .................................................................................... DS - 12

DS.4 CM-60 SELECTION GUIDE.......................................................................................... DS - 16

DS.5 BALLAST RESISTOR SELECTION GUIDE.................................................................... DS - 16

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 363 364

AMX AXD-CP4/PB Especificaciones Pagina 8

Comentarios a estos manuales