AMX RMS CODECRAFTER Guía de instalación descargar pdf (Pagina 19)

RMS Enterprise Installation Checklist

RMS Enterprise - Installation Checklist

NI Central Controllers and Enova All-In-One Presentation Switchers that come equipped with 64MB of RAM

(and therefore could potentially experience this error) are listed in the following table:

To avoid this error, it may be necessary to increase the Duet memory allocation on the NI Controller or

DVX-2100HD switcher. The Duet memory allocation setting can be viewed and adjusted via the telnet

terminal commands described below:

There are some considerations when doing this:

The higher you increase the Duet memory, up to a maximum of 64Mb, the less memory there is for

the NetLinx code to run. To find out how much Duet memory you need to run your program is by

trial and error.

We recommend increasing it by 2Mb, then trying to run your program. Repeat this process until

your code runs as expected.

It is important to keep the amount of memory allocated to Duet as low as possible so there is

maximum memory to run the NetLinx code.

Setting the Duet Memory Allocation Value

1. Telnet into the Controller (refer to the relevant Operation/Reference Guide for details).

2. Type SET DUET MEMORY. You will be presented with how much the memory is currently set to and a

prompt for the new setting.

3. Enter the new setting (such as 14 to set the Duet memory allocation to 14MB), then press ENTER.

NI Central Controllers and Enova All-In-One Presentation Switchers With 64MB of RAM

NetLinx Integrated Controllers Enova DVX All-In-One Presentation Switchers

NI-700 FG2105-70 DVX-2100HD FG1905-04, FG1905-05, FG1905-01, FG1905-02

NI-900 FG2105-90

NI-2100 FG2105-04, FG2105-14

NI-3100

* FG2105-05, FG2105-15

NI-3101-SIG FG2105-08

NI-4100

* FG2105-06

* The NI-3100 and NI-4100 are available with 256MB of SDRAM installed. Check the online catalog at

www.amx.com for details.

Enova DVX-2150HD/2155HD and DVX-3150HD/3155HD All-In-One Presentation

Switchers come equipped with 256MB of RAM. NI Controllers and Enova DVX

Switchers with 256MB of RAM should not experience this issue, since their default

Duet memory allocation setting is 36 MB.

DUET MEMORY Telnet Commands

GET DUET MEMORY Display the amount of memory allocated for Duet Java pool.

This is the current Java memory heap size as measured in Megabytes.

An example is a value of 12 = 12MB.

SET DUET MEMORY Set the amount of memory allocated for Duet Java pool. This is the current Java

memory heap size as measured in Megabytes. This feature is used so that if a NetLinx

program requires a certain size of memory be allotted for its currently used Duet

Modules, it can be reserved on the Central Controller.

The default Duet memory allocation value for NI Central Controllers with 64MB of

SDRAM (as well as the DVX-2100HD) is 12MB

Note: This setting does not take effect until the next reboot.

Terminal commands can be sent directly to the NI Controller or DVX-2100HD via

either a Program Port or a Telnet terminal session. In your terminal program, type

"Help" or a question mark ("?") and <Enter> to access the Help Menu, and display the

supported Program port commands.

Refer to the "NetLinx Integrated Controllers WebConsole and Programming Guide"

for a full listing of supported telnet terminal commands.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 135 136

Comentarios a estos manuales

Sin comentarios

AMX RMS CODECRAFTER Guía de instalación Pagina 19

Comentarios a estos manuales

Relacionado con productos y manuales para Software AMX RMS CODECRAFTER