AMX BCS Manual de usuario descargar pdf

Quick Start Guide

AutoPatch Optima Distribution Matrix

Overview

Because the Optima Distribution Matrix is available in two sizes (2 RU and 3 RU) and

various board configurations, the illustrations in this guide may differ from the model(s)

you purchased. For complete documentation for this product (including individual

board specifications), see the Optima Instruction Manual on the AMX AutoPatch CD or

at www.amx.com. This product supports full Device Discovery through AMX’s

AutoPatch Duet module (firmware v1.4.1 or higher is required).

Installation

Rack Mounting

To rack mount an Optima enclosure:

Linking Multiple Enclosures (if applicable)

If the system has multiple enclosures, cable(s) for linking and the Quick Start Guide

AutoPatch – Linking Enclosures have been provided. Link the enclosures according to

the guide.

Attaching Input and Output Cables/Wires

Before connecting all input and output cables/wires, attach only the first two inputs and

outputs and execute a test switch (see “Completing the Installation” on the next page).

When the test switch is successful, attach the rest of the input and output cables and

wires according to the AutoPatch Connector Guide. Follow the guide exactly; the

system is programmed to operate based on the guide.

Video I/O Boards – BNC

Video BNC connectors are used for standard video, wideband video, Hi-Z sync,

HV Hi-Z sync, Y/c, SD-SDI, and HD-SDI signal types.

S-Video I/O Boards

S-Video boards are equipped with locking connectors, which lock on to AMX

AutoPatch S-Video cables. Standard S-Video connectors may be used, but will not

lock.

To fasten a locking S-Video connector:

1. Hold the connector at a slight angle to the right and push in.

Pull back on the connector housing while pushing in.

RGBHV/HD-15 I/O Boards

RGBHV/HD-15 boards use HD-15 connectors.

Note: 55 mA is supplied on Output Pin 9; power draw not to exceed 50 mA per port.

DVI I/O Boards

EDID Programmer software is provided for the 8x8 DVI boards to assist with in-field

programming of custom EDIDs (4x4 DVI boards do not support this software). For

information, see the Optima Instruction Manual.

DVI Output Pin 14 (+5 VDC out):

• On the 4x4 DVI board, Output Pin 14 supplies 55 mA; power draw not to exceed

50 mA per port.

• On the 8x8 DVI board, Output Pin 14 supplies 1000 mA shared total available on

Output 1 through Output 4 and 270 mA shared total available on Output 5

through Output 8. For installation information for the High-Amperage Outputs on

the 8x8 DVI board, see the Optima Instruction Manual.

HDMI I/O Boards

The HDMI I/O board has 8 input and 8 output HDMI connectors. It is HDMI 1.3

compatible and fully HDCP compliant. Priming the system for InstaGate

technology*

(pre-authorization of all connected source and destination devices) significantly

reduces HDCP latency (time required for authentication) in the matrix switcher for

HDCP negotiations with all displays in a system (see the Optima Instruction Manual).

* Some destination devices have a longer lag time than others between receiving a

signal and displaying that signal. Although InstaGate

reduces latency in the matrix

switcher, it cannot reduce the lag time inherent in a device.

If needed, EDID Programmer software is provided to assist with in-field programming

of custom EDIDs (see the Optima Instruction Manual).

Stereo Audio I/O Boards – 5-Term

Note: When using shielded twisted-pair wire, connect the shield (ground) at one end

only (recommend receiving end) to minimize low frequency noise (see FIG. 5 below).

Source and destination devices require either balanced or unbalanced connections.

More than one of the options shown in FIG. 5 can be used in the same system.

General Specifications

Approvals CE, UL, cUL, RoHS

MTBF 92,000 hours

Operational Temperature 32° F to 110° F (0° C to 43° C)

Storage Temperature -22° F to 158° F (-30° C to 70° C)

Humidity 0 to 90% non-condensing

2 RU Enclosures 3 RU Enclosures

AC Power

100 VAC to 240 VAC single phase

(50 Hz to 60 Hz)

1.8 A @ 100 to 240 VAC (max.)

AC Power

100 VAX to 240 VAC single phase

(50 Hz to 60 Hz)

3.3 A @ 115 VAC (max.)

1.6 A @ 230 VAC (max.)

Power Consumption

160 W per enclosure (max.)

100 W per loaded enclosure (typical)

Power Consumption

260 W per enclosure (max.)

135 W per loaded enclosure (typical)

Thermal Dissipation

546 BTU (max.)

341 BTU per fully loaded enclosure (typical)

Thermal Dissipation

887 BTU (max.)

461 BTU per fully loaded enclosure (typical)

Dimensions

Approximately 12 in. (30.5 cm) depth

18.9 in. (48.0 cm) width with rack ears

17.4 in. (44.2 cm) width without rack ears

3.5 in. (8.9 cm) height

Dimensions

Approximately 12 in. (30.5 cm) depth

18.9 in. (48.0 cm) width with rack ears

17.4 in. (44.2 cm) width without rack ears

5.2 in. (13.2 cm) height

Weight

Approximately 10 lb. (4.54 kg)

per loaded enclosure

Weight

Approximately 12 lb. (5.44 kg)

per loaded enclosure

FIG. 1 Attach rack ears to sides of enclosure

FIG. 2 Three BNC connectors are required for a three-component signal

1. Attach the rack ears as shown left (screws provided).

2. Install in a rack leaving a minimum of one empty rack

unit above and below (required); three empty rack

units above and below are recommended.

Note: Component signals (e.g., Y/Pb/Pr)

require more than one BNC connection.

The example to the left shows three BNC

cable connectors attached for routing a

three-component signal through Output 9.

FIG. 3 Pull back on connector housing while pushing in

FIG. 4 5-Term stereo audio wiring

FIG. 5 Options for source-to-Optima-to-destination 5-Term wiring

Connector housing

Balanced audio

Unbalanced audio

Note: Audio boards with 5-position

terminal block connectors can be

wired for balanced (differential) or

unbalanced (single-ended) audio.

Inputs

Outputs

1 2

Quick Start Guide 1

Indice de contenidos

Pagina 1 - Quick Start Guide

Quick Start GuideAutoPatch Optima Distribution MatrixOverviewBecause the Optima Distribution Matrix is available in two sizes (2 RU and 3 RU) and vari

Pagina 2

Mas documentos para Software AMX BCS

a Ver el documento AMX BCS Información técnica

AMX BCS Información técnica (47 paginas)

a Ver el documento AMX BCS Manual de instrucciones

AMX BCS Manual de instrucciones (53 paginas)

Comentarios a estos manuales

Sin comentarios

AMX BCS Manual de usuario

Busca en linea o descarga Manual de usuario para Software AMX BCS. AMX Optima QSG REV D.fm Manual de usuario

Indice de contenidos

Mas documentos para Software AMX BCS

Comentarios a estos manuales

Relacionado con productos y manuales para Software AMX BCS